Hold the Alt key and press the PrtScn key. To post a screen shot of the active window. Note: the signal level is a negative number, so for example -88 is worst and -40 is better "A desirable signal level for a robust Wi-Fi connection will be green". Post which SSID name is yours, its located in the list, under network "Adapter Name" (1st column)įor a reliable (or robust as the Xirrus user guide says) wireless connection you need a signal of about -70 dBm or better. If there are a lot of networks showing can you click on "networks" top lefthand area - so we can see all the network information. Post a screen shot of the program running. net framework is needed, and included in that message is a link to download/install. On windows 8 - (i do not have windows 8) but, it would appear that, When you first try to run, you may get a message that. If you get an error - You will need to have NET Framework installed for the WiFi Inspector to function. Then run and install the program - on a wireless enabled PC/Laptop There is also a xirrus gadget, But that does not have all the fuctionality "DOWNLOAD GADGET Vx.xxĭo NOT use any of the download managers offered - Cnet, just use the direct link below - and click on the download button ( the site now appears to allow webbased emails like gmail, hotmail, outlook and yahoo now ) If you do not have another PC - do you have a phone connected to the internet - can you photograph the result and post the image in a replyĭownload this file "DOWNLOAD WI-FI INSPECTOR Vx.xx " You will now need to take a screen shot and copy that back to the working PC and attach the screen shot in a reply on the forum here. Plug it into the working computer with internet access and copy the file to the faulty PC and install the program. Save the file to a USB flash drive or other removable media. If you cannot access the internet with this PC, then you will need to copy the program across to the faulty PC Lets see an xirrus - leave it running until it disconnects and then lets see a screen shot please There maybe interference or a conflict with any wireless utilities that may have also been installed Note: For devices with non-standard Bluetooth protocols, there may be some compatibility problems.Have you checked for any new drivers online The models supported are much more than the ones listed. (2) The following compatibility list is based on the TP-Link lab environment. (1) Make sure that your device has Bluetooth function. Please refer to Q7 to check out the compatibility list. For the devices with non-standard Bluetooth protocols, there may be some compatibility problems. And then try to scan one more time on Bluetooth USB Adapter and you will be able to find the device.Ħ. Right click on that device and select Remove device. Go to Control Panel > Hardware and Sound > Devices and Printers, and then you will find the devices that was previously connected to your Bluetooth USB Adapter on the Devices page. So please try the following steps on your PC before another scan: Once the device was paired, it cannot be scanned again unless you delete it. Please follow this instruction to install it: How to install the Bluetooth Nano USB Adapter?ĥ. Please try to manually install the driver again. Or disable it in the Device Manager and enable it again.Ĥ. Please unplug the Bluetooth USB Adapter and reinsert it. Reboot the Bluetooth device and computer.ģ. Make sure your Bluetooth device is set to be discoverable.Ģ. If you're watching videos or streaming music from an ONLINE source, please make sure the audio dropout issue is not caused by slow network speed.ġ. Operation range can be affected by physical obstructions (walls, people, etc.) and wireless interference (Wi-Fi routers, Wireless TV adapters, etc.). Please test your receiving Bluetooth device with a mobile phone to confirm its range is acceptable. The Bluetooth range depends on BOTH the receiving and the transmitting devices. If your device is having range issues when plugged into a USB 3.0 port, a USB extension cable can help with this.Ģ) Ensure the Bluetooth receiver has a good signal Because there is a lot of random radio noise generated by the processor and system parts which will cause the short-range and cut off issue.Īn Intel white paper was confirmed that poorly shielded USB 3.0 ports will cause radio interference. Please move the adapter to the front of the computers instead of the back of the computer or using a USB 2.0 extension cable to move the adapter away from the computer. 1) Change to another USB port or use a USB extension cable
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |